Power and service processors

Service processors are reached out of band, so a machine that will not boot can still be talked to.

Redfish is tried first, because IPMI over LAN ships disabled on current iLO, XCC and iDRAC firmware and trying it first only produces timeouts. Where IPMI is used, the tools run on the host with a route into the management network and the password never reaches an argument vector.

bmc.order, or the order of a node’s vendor profile, says which transports to try and in which order; redfish and ipmi are the only entries it takes. Reading the power state falls back to the next transport when the first fails. An action falls back only when the first provably never reached the service processor, because its name did not resolve or nothing accepted the connection; one that may have arrived is never sent again. A processor that presents another certificate than the one recorded never receives the request either, since the certificate is refused before it is sent, but it is not tried over another transport: it may not be the processor, and its account goes to it over no protocol. provision reinstall counts it the same way, as unreachable, and exits 3. --ipmi uses IPMI alone.

Reading state

$ clusterctl bmc status -n '@rack:R02'
NODE     STATE  ERROR
exe0001  On
exe0002  On
exe0003  Off
exe0004         exe0004.mgmt.hpc.example.org: dial tcp: i/o timeout

$ clusterctl bmc redfish info -n exe0001 -o wide
NODE     POWER  HEALTH  MODEL           BIOS  RESET TYPES
exe0001  On     OK      Vendor Model X  2.1   On,ForceOff,ForceRestart,GracefulRestart,PowerCycle

reset types is what that firmware actually accepts. It is worth looking at once per hardware generation.

Every node gets a row, and the exit code says the worst thing that happened: 3 when a service processor could not be resolved, reached or trusted, 2 when a credential is missing, 1 when one answered with a refusal. A missing credential stops the command before anything is sent.

Changing state

$ clusterctl bmc power soft  -n exe0003     # ask the OS to shut down
$ clusterctl bmc power off   -n exe0003     # cut the power
$ clusterctl bmc power on    -n '@rack:R02'
$ clusterctl bmc power cycle -n exe0003
$ clusterctl bmc power reset -n exe0003     # without asking the OS

Every one of these previews and asks:

$ clusterctl bmc power off -n '@rack:R02'
About to power off 10 hosts: exe[0001-0010]
  through Redfish, falling back to IPMI with the credential bmc
This is more than 8 hosts. Type the number of hosts to continue: 10

A set whose nodes use different transports or accounts shows one line for each group, and each group of IPMI nodes goes to the backend with its own account.

$ clusterctl bmc power off -n exe0007
clusterctl: exe0007 is running Slurm jobs; drain them and wait for their jobs to end, or pass --lose-jobs to lose the jobs

The check refuses whatever it cannot vouch for: a state it does not know, a node sinfo does not list, and every node when Slurm cannot be asked. A node whose Slurm name differs from its inventory name is refused this way:

$ clusterctl bmc power off -n exe0007
clusterctl: Slurm did not report exe0007, so whether it runs jobs is not known (check that the Slurm and inventory names agree); pass --lose-jobs to go ahead and lose any jobs on them

safety.slurmAware turns the check on or off and is on by default. With it off, every power action says so before it asks. --dry-run asks Slurm as well, so a dry run is refused where the real run would be.

Powering on a rack

A rack powering on at once trips its breaker, so a power-on is sent in batches, and so is a power cycle, which powers the rack on again. The set is split evenly, so ten nodes in batches of at most 8 go as 5 and 5:

$ clusterctl bmc power on -n '@rack:R02' -y
powering on exe[0001-0005] (1 of 2)
waiting 5s before the next batch
powering on exe[0006-0010] (2 of 2)

safety.powerOnBatch and safety.powerOnStagger configure it; --batch and --stagger override for one command. A value given there is used as given: --stagger 0 does not pause, and --batch below 1 is refused, like safety.powerOnBatch, rather than sending the whole set at once.

A batch with a failure stops the run, because the failure may be the breaker. The result still lists every node, those of the later batches as not tried:

clusterctl: 1 of 10 service processors failed, 5 not tried: exe[0006-0010]

A reset is sent once

A reset that timed out may already have been carried out, so nothing retries it: sending it twice would power cycle a running machine. If a reset times out, read the power state and decide.

Ctrl-C stops sending and exits 130. Nodes nothing was sent to read not sent; an action that was under way reads outcome unknown, because it may have been carried out, and a read that was under way reads interrupted. The summary counts these apart from the failures.

An unsupported reset type is refused before it is sent

$ clusterctl bmc power soft -n exe0001
clusterctl: exe0001.mgmt...: does not accept the reset type "GracefulShutdown";
  it accepts ForceOff, ForceRestart, GracefulRestart, On, PowerCycle

The machine is asked what it accepts rather than guessed at. Firmware that lists its reset types in a separate @Redfish.ActionInfo resource is followed there, and when that resource cannot be read the reset is not sent. A vendor profile’s resetTypes (see Firmware that differs) takes the place of what the machine says, for firmware that advertises a type it then rejects.

What a machine boots next

$ clusterctl bmc boot show -n exe0001
NODE     SOURCE  MODE      ERROR
exe0001  None    Disabled

$ clusterctl bmc boot set Pxe -n exe0001
$ clusterctl bmc boot unset -n exe0001

Certificates

A service processor carries a self signed certificate that no authority vouches for. clusterctl records the one it sees first and refuses a change, the way ssh does with host keys. It says so when it is about to record one, so that a first contact you did not expect is noticed:

$ clusterctl bmc status -n exe0042
no certificate is recorded for exe0042.mgmt.hpc.example.org yet; the one it presents now will be recorded and trusted from then on

The certificate is recorded under the host clusterctl talks to: the bmcAddress of the node when the inventory sets one, otherwise the name the naming rules give.

$ clusterctl bmc status -n exe0001
clusterctl: the certificate of exe0001.mgmt.hpc.example.org changed:
  recorded sha256:1a2b…, now sha256:9f8e….
  If the certificate was replaced on purpose, run "clusterctl bmc forget exe0001" and try again

$ clusterctl bmc forget exe0001
About to forget the certificates of 1 host: exe0001
  drops from /home/admin/.local/state/clusterctl/bmc-pins:
    exe0001.mgmt.hpc.example.org sha256:1a2b…
Continue? [y/N] y
forgot the certificate of exe0001.mgmt.hpc.example.org, sha256:1a2b…

The node’s name works, and so does the service processor’s as the error gives it. Forgetting goes through the same confirmation as any other change, and --dry-run shows the fingerprints without dropping them. Do it after replacing a certificate on purpose. If it changed and nobody replaced it, find out why first: the next connection trusts whatever it is shown.

When several commands reach a new service processor at the same time, only the certificate recorded first is accepted; one that presents a different certificate in the meantime is refused like a change.

A redirect is never followed. Following one would send an action a second time, and could send the credentials to the same host over plain HTTP, so the command stops and names where the service processor pointed.

Talking to Redfish directly

$ clusterctl bmc redfish get /redfish/v1/Systems/1 -n exe0001
$ clusterctl bmc redfish get /redfish/v1/Managers -n exe0001 \
    -o jsonpath='{.exe0001.Members[*]}'
$ clusterctl bmc redfish post /redfish/v1/Systems/1/Actions/ComputerSystem.Reset \
    '{"ResetType":"ForceRestart"}' -n exe0001

post can power off a machine, so it goes through the same confirmation as any other destructive command.

Firmware that differs

bmc:
  vendors:
    vendor2:
      resetTypes: [On, ForceOff, ForceRestart, GracefulRestart, PowerCycle]
      systemPath: /redfish/v1/Systems/Self
      minTlsVersion: "1.0"

Keyed by the node’s vendor attribute in the inventory. This is how a generation of hardware with unusual firmware is handled without a code change. When resetTypes is set, a reset is checked against it instead of against what the machine advertises.

Rack power

$ clusterctl pdu list
RACK  PDU                       NODES
R01   pdu0-R01.mgmt.example.org  dbm01,wlm01
R02   pdu0-R02.mgmt.example.org  exe[0001-0010]

$ clusterctl pdu shell 1 R02
$ clusterctl pdu shell 1 R02 -- show outlets

Which processors answer

$ clusterctl bmc ping -n '@rack:R02'
BMC                           STATE
exe0001.mgmt.hpc.example.org  alive
exe0004.mgmt.hpc.example.org  no answer

9 of 10 answered

One sweep from the gateway, not one connection per processor. A processor that does not answer exits 1; a sweep that could not run, because fping is missing or the gateway cannot be reached, exits 3 rather than reporting every processor as down.